Bulletin#		Subject		Date
376		Fuel Flop Tube Hose Assembly		5-26-2008
375		Optional Concorde RG-25 Battery Installation		3-15-1996
374		New Extruded Fiber Washer will replace the Original Insulator on Mike Jacks		10-20-1995
371		Control Stick Hand Grips		10-1993
370		Fuel Quantity Site Tube & Flop Tube Assembly		10-1993
369		Baffle Reinforcements Added to Eagle II Aircraft 918 Engine Equipment Kit		12-5-1984
368		Addition of Rubber Friction Rings to Vent Valves on the Eagle II		12-4-1984
366		Centerline marks on Spar Splice Fixture use in Construction		12-4-1984
364		Modification of Landing Gear Strut Mounting		11-20-1984
362		Aileron Braces Omitted from Eagle II Aircraft 901 Ailerons Kit		7-23-1984
360		Oil Leakage from 915 Canopy Snubbers		3-5-1984
358		Exhaust Snubber Kit		2-8-1984
357		Lycoming Service Bulletins 465 and 465A Concerning Crankshaft Propeller Flanges		2-8-1984
356		New Type Braces for Ailerons		2-2-1984
342		Installation of Inspection Rings in Fabric of Upper and Lower Wings		12-30-1983
341		Access Doors Available		12-28-1983
333		AVCO/Lycoming Service Bulletin 465 concerning Crankshaft Propeller Flanges		11-3-1983
332		Cockpit Heater System Available		10-21-1983
331		Propeller Flange Failures on Lycoming Engines		9-19-1983
329		Leaking Fuel Tank		8-25-1983
324		Procedure Added to Fuel Tank Filler Mod Described in Earlier Product Letter 306		6-25-1983
322		Change of Finish on Socket Head Cap Screws		6-9-1983
321		Installation of Anti-Chafe and Anti-Vibration Tape on Propellar Hub		6-4-1983
319		Installation of Wind Leading Edges		6-4-1983
318		Tensioning of Drag and Anti-Drag Tierods in Upper and Lower Wings		6-4-1983
317		Inspection of Landing Gear Support Structure on Fuselage		6-3-1983
315		Tire Filler Acess		5-24-1983
313		New High-Performance Battery		5-16-1983
312		Carbon Monoxide Detection		5-17-1983
311		Horizontal Stabilizer Incidence		5-12-1983
309		Installation of Fairings and Gap Seals		5-12-1983
307		New Digital Chronometer System		5-10-1983
306		Relocation of Fuel Filler Port		5-10-1983
305		Addition of Hydrolic Snupper to 915 Canopy Kit		5-4-1983
304		Continuing Delay in Delivery of 911-FD Fuel Display Kit		5-2-1983
302		Revision of Fuselage and Canopy Aft Hinge Modification Procedure in Product Letter 295		4-5-1983
297		Change of Fuel Sight Guage Material in 909 Fuel System Construction Kit		3-22-1983
296		Delivery of 911-FD Fuel Display Kit		3-21-1983
295		Change of Canopy Aft Hinge Attachment in 904 and 915 Construction Kits		3-14-1983
294		Addition of Canopy Frame Stiffener and New Oil Cooler Mounting Parts to 620 Cowling Kit		3-11-1983
292		Bendix Magneto Service Bulleting 623 - May Apply to Lycoming Engines		2-21-1983
291		Addition of Canopy Roller Assembly to 915 Canopy Kit		2-21-1983
276		New Digital Fuel Quantity and Fuel Flow Display System		9-16-1982
272		Retention of Edo-Aire Radios		9-16-1982
271		Stainless Steel Hardware Addition to 918 Kit for Exhaust Manifold Slip-Joints		9-15-1982
270		Luggage and Tiedown Storage Kit		9-15-1982
269		New Style Flying Wire Javelins		7-27-1982
268		Cracks in Exhaust Manifold Assemblies		7-26-1982
264		New Battery Clamp Adapter to prevent Possible Electrical Short		7-14-1982
263		Landing Gear Fairings Redesigned to Simplify Installation		7-14-1982
262		New Type Anti-Chaffing Material for Canopy Skirt		7-14-1982
260		Incorrect Park Number Marking of Control Sticks		5-4-1982
257		Proper Installation of Engine-Attach Bolts and Possible Requirement for Bolt Inspection		3-5-1982
256		Incorrect Clevis Bolts Supplied with Previous Product Letter 251		3-2-1982
255		Clarification of Wood Grain Description in Previous Product Letter 252		2-27-1982
252		Inspection of Wing Tierod Blocks		2-16-1982
251		New Hardware for Attachment of Rudder Cable Clevises to Rudder Horns		2-15-1982
250		Ignition Switch		1-8-1982
249		Change of Interplane Strut Mounting Hardware		12-14-1981
248		Inspection of Hinge Pin		12-14-1981
246		FAA Form 8610-2 and 8130-6 added to 924 Flight Kit		10-26-1981
245		Baffle Box added to 918 Engine Equipment Kit		10-26-1981
244		Canopy Brace Inspection		10-08-1981
243		Rear Hinge Assembly Inspection		12-14-1981
242		Incorrect Nutplate Packaged in 915-H4 Hardware Kit		9-22-1981
241		Interim Weight and Balance Data and Flight Manual Data		9-9-1981
239		New Part, ELT Locking Clip		8-4-1981
235		Interim Weight and Balance Data and Flight Manual Data		6-19-1981
234		Tapered Washers for Mounting Interplane Struts		6-15-1981
233		Redesigned Alternate Air Door		6-15-1981
232		Design Modifications by Homebuilders		6-15-1981
228		Rudder Cables Omitted from 908 Cockpit Equipment Kit		5-27-1981
224		Locking Lug for Edo-Aire Radios in 912 NAVCOM Kits		5-26-1981
223		Interim Weight and Balance Data and Flight Manual Data		5-11-1981
218		Fitting of Wing Tip Bows in 902 and 903 Wing Kits		4-23-1981
217		Possibility of Incorrect Parts in 915 Canopy Kit		4-22-1981
215		Interim Flight Manual Data		4-14-1981
214		Interim Weight and Balance Data		4-10-1981
213		Oil Cooler Port Fittings for Lycoming Engines		4-6-1981
212		Interim Weight and Balance Data		3-19-1981
211		Product Manuals		3-7-1981
207		Interim Weight and Balance Data		2-20-1981
205		Mechanical Fastening of Edo-Aire Radio Sets		2-16-1981
204		List of Constrution Tool Requirements		2-8-1981
202		Typographical Errors in Interim Weight and Balance Data		2-3-1981
201		Revised Inspection Plate for Aileron Pushrod Cover		2-13-1981
199		Trimtab Horn on Early Fiberglass and Aluminium Trimtab Assemblies		2-13-1981
198		Inspection Plates supplied in 923 Kit		1-27-1981
197		Canopy Guide Bushings moved from 915 Canopy Kit to 907 Fuselage Equipment Kit		1-28-1981
196		Incorrect Bolt in 907 Kit		1-27-1981
195		Incorrect Bolt in 905 Kit		1-27-1981
194		New Canopy Jettison Tab in 915 Canopy Kit		1-12-1981
192		Existing Placards Revised and New Placards added to 923 Covering and Pre-Finish Kit		12-17-1980
189		Corrected List of Effective Pages in 903 Manual Revision 13		11-14-1980
187		Increased Length of Bushing Welded to Vertical Fin for Attachment of Tail Wire Brackets		11-11-1980
186		Tab Dividers for 912 NAVCOM Product Manual		11-11-1980
185		Illustration Missing from page J-26A of the 903 Manual Revision 13 Pages		11-4-1980
184		Changed Hardware for Attachment of Governor Control Cable to Governor Control Arm		11-4-1980
183		Lycoming Service Bulletin 245C		10-28-1980
181		Increased Length of Bushing Welded to Vertical Fin for Attachment of Tail Wire Brackets		10-16-1980
179		Possibility of Defective Threads in 50130-009 and 50130-010 Tierod Terminals		10-16-1980
177		New Parts added to the 923-L Covering and Prefinish Kit		10-16-1980
176		New Parts and Materials added to the 923 Covering and Prefinish Kit		10-16-1980
174		Extra Inspection Rings for Optional Inspection Holes		7-23-1980
173		Extra Inspection Rings for Optional Inspection Holes		7-11-1980
172		Revised Hardware for attaching Pushrods in Manual Steps A-5 and B-8		7-11-1980
171		Transfer Marking Stud		7-11-1980
169		Electrical Panel Placard Incorrectly Identifies Left and Right Magneto Position		7-9-1980
167		Addition of Ventilation Air Outlets		6-13-1980
166		Relocation of Conopy Lock Panels and Hardware from915 Canopy Kit to 908 Cockpit Equipment Kit		6-13-1980
165		Manual Error in Step A-25. Revised Procedure for Attachment of Airscoops and Vent Covers		6-3-1980
164		Partial Assembly of 915 Canopy Kit in Preparation for Field Installation of Kit by Christen Personnel		5-14-1980
163		Repolitioning of Nutplate Tabs at Station 31 of 904 Fuselage Structure		5-27-1980
162		Product Manual Parts List for 923 Covering and Prefinish Kit		5-3-1980
161		Inspection of Paint Coating on Early 904 Fuselage Structures for Presence of Rust		4-29-1980
160		Inspection of 904 Fuselage Structure for Presence of Tubular Elements		4-29-1980
159		Packaging Error in 923 Series Covering and Prefinish Kits		4-28-1980
158		Replacement of Filament Tape in 923 Covering and Prefinish Kits		4-27-1980
157		Delivery of 915 Canopy Kits and Field Installations by Christen Personnel		4-27-1980
156		Changes in 912 NAVCOM Kit		4-13-1980
155		Revised Product Brochures and New Price List		4-12-1980
151		Shipment of Air Vent Components which have Delayed on Backorder for 914 Kits		3-25-1980
150		Repositioning of Air Vents for best Appearance in both No. 1 and No.2 Paint Designs		3-21-1980
149		Correction of Stabilizer Incidence Angle in Manual		3-13-1980
148		Inspection of Welded Pushrod Assemblies		3-13-1980
147		Part Number Correction in Manual Step D-8		3-3-1980
146		Modify Spring to Eliminate Interferrence with Airbox		2-27-1980
145		Splice Plate added to Recontour Aft Portion of Turtledeck Cover		2-27-1980
144		Hinge Spacer and Washer Spacers Added		2-15-1980
143		Incorrect Parts in 920 Cowling Kit and Requirement for Replacement		1-25-1980
142		Hinge Spacer and Washer Spacera Added		2-13-1980
140		Added Large Area Washer and Changed Bold Length		2-8-1980
137		Modificatin of Fuselage former to ensure Adequate Clearance for Movement of Elevator Idler Pushrod		1-31-1980
135		920 Hardware Items Packaging		1-28-1980
134		Addition of a Second Angle Bracket with Attaching Hardware		1-29-1980
132		New Procedure for Checking contents of Kits		1-28-1980
131		Incorrect Parts in 920 Cowling Kit and Requirement for Replacement		1-25-1980
129		Inspection of Elevator Horn for Crack at Top Edge of Flange		1-29-1980
128		Inspect for Interference between Engine Oil Filler Tube and Engine Mount Member		12-27-1979
126		Inspect Elevator Control Linkage Idler Arm for Interference wtih Fuselage Cross Member		12-19-1979
116		50070-008 Flat Washer Replaces 50070-005 Flat Washer		12-12-1979
115		Part Number 31029-001 Engine Baffle Pilot Hole Location		12-12-1979
114		50195-003 Nutplate Replaced by 50195-009 Nutplate		12-12-1979
111		Procedure Error in 918 Manual Step F-13		11-29-1979
109		Inspection of Bolt Thread Engagement in Self-Locking Nut Described in Manual Step O-14		11-29-1979
108		Vender-Supplied Adapter Improperly Machined		11-26-1979
106		Paint Designs and Availablity of Masking and Painting Materials in 923 Kits		11-28-1979
102		Additional Hardware Required for 918 Kit in Accordance with Manual Revision 1		11-21-1979

You'll need Adobe Acrobat Reader to view our service bulletins and letters. Getting the Adobe Acrobat viewer is simple and free! Just click the Adobe icon to the left and follow the easy steps to download Acrobat.

Pitts® is a federally registered trademark of Aviat Aircraft, Inc.®